Cut Your own Faceted Gems - its not that hard by Chris Ralph

Cut Your own Faceted Gems - its not that hard by Chris Ralph
Cutting your own Faceted Gems is not that difficult - here are the steps of the process:
Step One: Selecting the Rough If you are interested in cutting your own gemstones, the starting point for any gem cutting is, of course, the rough. There are places in the US where you can actually dig and mine your own gemstones, but for most folks, getting rough means buying it. Gemstone rough comes from small mines all around the world, and most goes to commercial cutters, but there are a few dealers who specialize in selling rough, and it is possible to buy gemstone rough and save money. Sometimes rough looks like a crystal and sometimes it just looks like a chunk of colored glass. For the example I used on my website, I choose a piece of amethyst from Brazil that I purchased some years ago. The amethyst miners actually take the rough crystals of amethyst and strike it with hammers to knock off the flawed portions of the stone. This produces a clean piece of rough that has broken edges as shown in the photo on my site.
Step Two: Making the Preform The rough gem is then sawn with a diamond saw and ground into a shape close to that of the finished stone. The "shaped" rough is called a preform. A big key at this first step is to identify and remove any remaining flaws and then find the shape of the rough that will yield the largest stone out of what remains. The preform is sawed in diamond grit saws and ground on coarse grinding wheels. One side of the stone is cut with a flat surface - this will eventually become the table or main flat facet on top of the stone. In the beginning, this main flat facet is used to orient the rest of the stone. At this stage the stone is called a preform, and you can see what the final shape will be.
Step Three: Dopping the Stone In my example, a pear shaped preform is "glued" to the brass dop stick. The flat tops of these dops are matched to the flat table facet on the stone. The glue that is used is actually a special high temperature wax. In my example, the dopped preform has was been glued flat side down on to the brass dop stick. The rough end of the stone will be cut away to form the pointed base of the stone. Contrary to what a lot of people think, faceting is NOT a process of chipping or cleaving with a little hammer. This process is used for diamonds only and then only in place of sawing to prepare them for cutting. Regular faceting is a process of grinding and polishing - this is true with both diamonds as well as colored stones. One or two different grit flat lap wheels are used to grind in the facets and a polishing lap is used to put a final polish on them. Diamonds are cut and polished on one lap.
Step Four: Cutting the Stone on the Faceting Machine Here the preform is being cut and polished on a lap on my homemade faceting machine. The bottom part of the stone is cut first. Each flat facet is cut on a grinding lap, and then the lap is changed and each facet is polished on a polishing lap. The location of each is set by the toothed gear and angle protractor and the hand set. This is a polishing lap on the machine in the photo. My machine is partly home made. The mast and hand set are by Master Co., but the rest of the machine is home made. The mast set up is also old - it dates from the 1950s. In spite of that, it still works quite well. Twenty four facets on the cullet have now been individually cut and polished. Step Five: Cut and Polish the Cullet, Transfer The bottom part of the stone, (also called the cullet) has now been cut and polished - all the facets on the base are now polished and complete. Now it is time to flip it over and cut the upper portion of the stone, known as the crown. In order to do that, the stone must be transferred to another dop. The new dop will hold the base of the stone so that the top portion is exposed for cutting and polishing. As the first dop had a flat surface to match the table facet, the second dop has a "V" shaped notch to match the "V" shaped bottom of the stone.
Step Six: Polish the Table and the Crown The stone has now been transferred from the first dop in order to turn it over for polishing the top side of the stone - called the crown. The first facet to be cut and polished on the crown side is the top flat or table facet. In order to do this, a special 45 degree dop holder is needed to allow us to reach the table. This photo shows the table facet complete and polished but none of the rest of the other top (or crown) facets cut in - they are to be cut and polished next. After all the facets are cut in and polished, the stone is removed from the dop stick and cleaned to remove any remaining wax. The wax can be softened by gentile heat, and most of the wax removed. The rest of the wax used in this process washes off the stone when it is soaked in alcohol.
Step Seven: Set the Stone in Nice Jewelry In my example, the finished Amethyst stone - with all facets complete and the stone removed from the dop sick, cleaned is shown set in fine jewelry. If you take a look at my website, you will see that it turned out very nice, didn't it?
So there it is, the whole process from a lump of purple chunky glass like stone, to a beautiful gem.
To see photos of the gem and the equipment used in this process, and learn more about gemstone cutting and how you can do it yourself, take a look at my website. You can see and learn about it at: http://nevada-outback-gems.com/faceting_example/FACETING.HTM
If you are interested in learning more about where you might dig your own gemstone rough, take a look at my rock hound's web page at: http://nevada-outback-gems.com/Rockhound/Rockhound%20_Corner.htm
About the Author
Chris Ralph writes on small scale mining and prospecting for the ICMJ Mining Journal. He is a rock hound and prospector and owns his own turquoise mines in Nevada. His information page on gemstones can be viewed at: http://nevada-outback-gems.com/Encyclopedia_pages/Gemstone_Encyclopedia.htm